Jump to content

Recommended Posts

Posted (edited)

Say no to crack! Sorry, someone had to say it.

Crack is wack! :p ... What?... Too soon? :ph34r:

hehe! you guys crack me up! :D

sorry.. had to.. :p

Sheesh! you all crack me up! ....I've got nothing.. <_<

Hope someone will post any remedies on this one soon. I also have the same issue with my Alto's. :unsure:

Yeah, me to. Kinda one of the annoyances of the 25R's.

Edited by Hikaru1234567890
Posted (edited)

Personally, I disassembled that part (it's easy since there's a screw). Then I applied a layer super glue to the joint and put it back together. The hinge was tight afterwards.

Edited by ArchieNov
Posted

Personally, I disassembled that part (it's easy since there's a screw). Then I applied a layer super glue to the joint and put it back together. The hinge was tight afterwards.

I did that and the joint was tight as if it was new (put a little rubber in it)! But its the pin connecting to the joint thats loose.

Posted

post-21335-0-69157300-1422648927_thumb.jpg

Heres the shoulder hinge, I dare not take it off cause its a real pain to put it back together. Any advice on how to tighten it? and that is NOT a crack.

Joint "A" I was able to tighten up this joint a bit by adding a clear coat to ball joint and tightening the screw..

Joint "B" Cant quite remember if there is a screw or a pin in this joint.. Although I haven't had an issue with this joint. yet..

Joint "C" I managed to remove the pin and attempted to fit in a replacement but it wouldn't fit so well so I managed to expand the original pin ever so slightly and pushed it back in the joint and it seemed to work. Removing and replacing this pin is a total prick of a thing to do..

This whole area is just a weak point of the 25.. not necessarily a "bad" design, just poorly manufactured. I would say due to the complexity of the design in order for it to transform as accurately as possible that this was the best compromise.

But clearly manufacturing tolerances were not as closely refined as needed.

Posted

This whole area is just a weak point of the 25.. not necessarily a "bad" design, just poorly manufactured. I would say due to the complexity of the design in order for it to transform as accurately as possible that this was the best compromise.

But clearly manufacturing tolerances were not as closely refined as needed.

Yeah, I would have to agree with you. It is a complicated design to, But they probably could have done a little better on it. I mean, look at the PG Gundams over complicated shoulders. There not perfect, but the at least don't ware out so quickly.

Posted

you cant really compare it with PG gundam, it is both bigger and less complex design to be represented accurately. For Joint C, I just put a drop of clear varnish or pledge/future. Move it around so the whole pin gets covered. The effect though wears out fast so if you can do a similar fix like what spanner said, then that is the better solution

Posted

So I finally got my hands on a Detolf which is to be dedicated to my Valkyries. :)

This has precipitated the removal from the box of my VF-25G (only the second but probably the last time)

Now I grant you I have limited experience transforming these things,

but holy crap the hips were tight as a tight thing!! :o

the left shoulder is floppy as a floppy thing :mellow:

and could I get the head to slide back and out?!?!? :angry:

Took me about an hour to get it into batdroid without breaking anything.

I'm taking a break there and I'll add the super parts later - if I can manage it.

I might also take some pictures - maybe.

Posted

So I finally got my hands on a Detolf which is to be dedicated to my Valkyries. :)

This has precipitated the removal from the box of my VF-25G (only the second but probably the last time)

Now I grant you I have limited experience transforming these things,

but holy crap the hips were tight as a tight thing!! :o

the left shoulder is floppy as a floppy thing :mellow:

and could I get the head to slide back and out?!?!? :angry:

Took me about an hour to get it into batdroid without breaking anything.

I'm taking a break there and I'll add the super parts later - if I can manage it.

I might also take some pictures - maybe.

it just wouldn't be a Valkyrie if you didn't have to experience this! :lol::p

Posted

it just wouldn't be a Valkyrie if you didn't have to experience this! :lol::p

The joys of ownership indeed.

I've been searching through this thread and watching videos on YouTube all night because I can't quite get the chest area right.

The nose cone seems to end up way too far back and I can't figure out why.

Then I tried to go back to fighter mode and I can't now!!

I've got transformation blindness.

Time for bed.

Posted

The joys of ownership indeed.

I've been searching through this thread and watching videos on YouTube all night because I can't quite get the chest area right.

The nose cone seems to end up way too far back and I can't figure out why.

Then I tried to go back to fighter mode and I can't now!!

I've got transformation blindness.

Time for bed.

there are some very good transformation guides on anymoon.com have you checked these out?

Posted

Yup

there are some very good transformation guides on anymoon.com have you checked these out?

Yes. They were my first port of call.

Posted

*snip*

Joint "C" I managed to remove the pin and attempted to fit in a replacement but it wouldn't fit so well so I managed to expand the original pin ever so slightly and pushed it back in the joint and it seemed to work. Removing and replacing this pin is a total prick of a thing to do..

*snip*

Is there a way to tighten this without removing the original pin? Thanks in advance! :)
Posted

Ok I need help now!

I've watched so many transformation videos now and I still can't get it right.

I can't get the nose cone to come far enough forwards it seems. (Pic1)

It won't go any further than the hinge at the front of the neck piece (pic2)

Any suggestions on what I'm doing wrong?

Pic3 just for further illustration.

Plus I can't get it back to fighter now either. I've lost it.

post-17939-0-52527100-1422802169_thumb.jpg

post-17939-0-34912800-1422802282_thumb.jpg

post-17939-0-88100700-1422802344_thumb.jpg

Posted

Is there a way to tighten this without removing the original pin? Thanks in advance! :)

make the pin larger by coating it with any clear coat (varnish, nail gloss, etc).

Posted

Ok I need help now!

I've watched so many transformation videos now and I still can't get it right.

I can't get the nose cone to come far enough forwards it seems. (Pic1)

It won't go any further than the hinge at the front of the neck piece (pic2)

Any suggestions on what I'm doing wrong?

Pic3 just for further illustration.

Plus I can't get it back to fighter now either. I've lost it.

Is it stuck there, or could you reverse the transformation? I am guessing the torso is stuck on the front landing gear doors, binding it up.

Posted

I've had a similar problem myself before. The way I fixed it was to over-rotate the fuselage further backwards after flipping the back plate up, then pushing the neck plate up further. Hope that helps.

Posted

Thanks guys.

I don't know how I managed it but I'm guessing when I "broke its back" the first time I rotated the cockpit section the wrong way

(if that's possible) and as a result, the leading edge extension housing the hinge, was stuck on the wrong side and was stopping the nose section

from moving through.

I was definitely going at it the wrong way - I couldn't reverse transform from were I'd managed to get to but eventually found a remedy by unscrewing

the the hips and removing the legs, swinging the cockpit back to the correct side and now I've got the nose, shoulders and chest plate all correctly orientated.

What a faff. I still don't understand how I did it.

In the meantime I transformed both Alto and Ozma according to the guides on Youtube (thank you jenius) and had no such issues.

Anyway, he's taken up residence beside Skull Leader for now. Might add the super parts later (now that they have a chance of fitting!)

post-17939-0-87238300-1422815470_thumb.jpg

post-17939-0-46815200-1422815476_thumb.jpg

post-17939-0-15220300-1422815482_thumb.jpg

Posted

make the pin larger by coating it with any clear coat (varnish, nail gloss, etc).

Thanks chyll2! But in order to do that, I still need to remove the pin, correct?

Posted

If I did not already have 4 "Phoenix's" I would jump on that. I guess this is a lucky break for all the guys that missed out and refuse to pay $200++

  • 2 weeks later...
Posted (edited)

Wow!

Can't say I've ever seen that happen before. Buy it now at a decent price, plus free shipping - what's the catch?

Edited by mickyg
Posted

So is this what happens when Bandai produces enough to meet demand?

Posted (edited)

Wow!

Can't say I've ever seen that happen before. Buy it now at a decent price, plus free shipping - what's the catch?

I guess I'll find out.

Mhwaahahahahahahahahahahahahaha*thank god for huge tax refund*hahahahahahahaa

Edited by Duymon
Posted

Grrr, I thought the VF-25G reissue was announced lol.

If I did not have 4x Ozma's already maybe this would have been a good option.

Guest davidwhangchoi
Posted

So is this what happens when Bandai produces enough to meet demand?

+1

pass, if i didn't have 5 already i would bite

Posted

+1

pass, if i didn't have 5 already i would bite

What the heck are you going to do with 5 David? My train of thought was 1x Armor in fighter mode with the rest of the squad in supers. 1x with Armor in battroid mode then 1x to go with the Ozma supers I have and 1x naked. Now getting around to opening them all up and displaying has been my problem lol.

Guest davidwhangchoi
Posted (edited)

What the heck are you going to do with 5 David? My train of thought was 1x Armor in fighter mode with the rest of the squad in supers. 1x with Armor in battroid mode then 1x to go with the Ozma supers I have and 1x naked. Now getting around to opening them all up and displaying has been my problem lol.

three of them were by accident.

i ordered one from hlj but they cancelled it, so i panicked and ordered from another place that cancelled 2 on me. i ended up getting 1 on mandarake and one from cd japan. then the guy who cancelled all of a sudden sends me 3x so i just took em.

nice! you got 2x armors? that's awesome.

Edited by davidwhangchoi
Posted

Each time this thread gets bumped I hope it is for a 25g reissue. I have supers and tornado parts just sitting here waiting. Although, they are pretty neat on the YF-25.

Posted

My 3rd piece just came in the mail (after sitting in private warehouse).
Not sure if I should display it with Super Parts, or just keep it in the box as a backup spare, since I already have 2 more displayed in Armored Parts..

Posted

three of them were by accident.

i ordered one from hlj but they cancelled it, so i panicked and ordered from another place that cancelled 2 on me. i ended up getting 1 on mandarake and one from cd japan. then the guy who cancelled all of a sudden sends me 3x so i just took em.

nice! you got 2x armors? that's awesome.

Yeah I ended up buying a spare set just in case the day came I would be able to get more Ozma's, it eventually paid off. :D

Each time this thread gets bumped I hope it is for a 25g reissue. I have supers and tornado parts just sitting here waiting. Although, they are pretty neat on the YF-25.

My problem is I only have 1x VF-25G and it is armed with Supers and my Tornado parts are just sitting.

Posted

Hey guys, sorry if this was asked before, am a little lazy to browse this entire thread (and the previous ones before it), but has anyone every tried installing the missiles that came with the 1/60 DX VF-25 ver.1 Ghost + Weapons pack onto their renewal VF-25's?

I'm looking at how those missiles attached to the ver.1 1/60s and the attachment points look to be the same in the renewal version.

Thanks for any feedback!

Posted

Hey guys, sorry if this was asked before, am a little lazy to browse this entire thread (and the previous ones before it), but has anyone every tried installing the missiles that came with the 1/60 DX VF-25 ver.1 Ghost + Weapons pack onto their renewal VF-25's?

I'm looking at how those missiles attached to the ver.1 1/60s and the attachment points look to be the same in the renewal version.

Thanks for any feedback!

I have seen people post pics of the Galia 4 speaker pods clipped onto the wings of the v2's. I think it is a similar connector.

Posted

Do the japanese know something we don't? There have been two ozma renewal armor sets on mandarake for over a week now when they usually sell in hours. It's strange enough that two sets would be dumped on mandarake at the same time and even stranger they're not selling.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...