misterryno Posted January 12, 2008 Share Posted January 12, 2008 Hey all, I just now took apart my G1 JetFire in order to soak the parts so that I may strip that paint off and repaint him myself or send him to get painted. My question is more so for the fast packs though. I was going to spray paint them black and I am not sure of the process of doing so that the paint will stick well and not come off. Can someone please give me some advice? THANKS. Quote Link to comment Share on other sites More sharing options...
nightmareB4macross Posted January 12, 2008 Share Posted January 12, 2008 Hey all, I just now took apart my G1 JetFire in order to soak the parts so that I may strip that paint off and repaint him myself or send him to get painted. My question is more so for the fast packs though. I was going to spray paint them black and I am not sure of the process of doing so that the paint will stick well and not come off. Can someone please give me some advice? THANKS. Clean, Sand, Prime, Sand, Spray...VIOLA!! Quote Link to comment Share on other sites More sharing options...
misterryno Posted January 12, 2008 Author Share Posted January 12, 2008 Clean, Sand, Prime, Sand, Spray...VIOLA!! Thanks....I'll have to see what I can do. Quote Link to comment Share on other sites More sharing options...
big F Posted January 12, 2008 Share Posted January 12, 2008 Yeah clean and sand is the really good advice make sure you get a good plastic primer as the paint can peel off a few months after painting otherwise. Clean your hands before handling too as the oils in your skin can affect the paint too. Best bet is to get yourself some of the disposable latex gloves as used by doctors in the hospitals etc. You can get a box of a 100 for a buck or two. Quote Link to comment Share on other sites More sharing options...
MechTech Posted January 12, 2008 Share Posted January 12, 2008 You didn't say airbrushing so I'm guessing spray can? If so, put it in warm (not hot) water and bring the cans up to a slightly warner temp. It helps the paint flow ,settle and cure smoothly. Keep the parts warm too, just not in the water . - MT Quote Link to comment Share on other sites More sharing options...
Skull-1 Posted January 12, 2008 Share Posted January 12, 2008 I don't prime usually. It just makes it thicker and easier to rub off. If your primer and paint are the same color it is less an issue. Sand the hell out of *everything* especially where parts rub. Use light even coats. Rustoleum and Duplicolor are the best spraypaints you will find... The advice from previous posters valid as well. Quote Link to comment Share on other sites More sharing options...
misterryno Posted January 12, 2008 Author Share Posted January 12, 2008 big F & MechTech, Hey you 2 thanks for the awesome advice. And yes Mech I am planning on using Spray Paint. For right now I can't justify spending the money on a AirBrush kit especially cause I don't know how to use one. I am sure it is pretty easy to learn, but the money is the issue right now. THANKS GUYS. Quote Link to comment Share on other sites More sharing options...
misterryno Posted January 12, 2008 Author Share Posted January 12, 2008 I don't prime usually. It just makes it thicker and easier to rub off. If your primer and paint are the same color it is less an issue. Sand the hell out of *everything* especially where parts rub. Use light even coats. Rustoleum and Duplicolor are the best spraypaints you will find... The advice from previous posters valid as well. THANKS Skull-1, I have actually considered just asking you if I can send all the parts to you to do a paint job for me. But I think I may try to learn myself and not burdon you with my issues of painting . Quote Link to comment Share on other sites More sharing options...
mitch Posted January 13, 2008 Share Posted January 13, 2008 While we're on the topic of spray painting, I'm psyching myself up to start taking apart a bandai VF-19S Blazer. I want to paint it so that the finish is as durable as possible so I can keep playing with it (the bandai VF-19S is obviously not really a display piece is it ). So with that in mind, does anyone have any experience with KRYLON FUSION spray paint? I seem to remember people saying it was really good at bonding to plastic, I'm just concerned adout wear at pivot points and joints. Obviously there will be some light sanding in order,and I'm told that it may take a week to completely dry, but I would really appreciate some words of wisdom from anyone who has taken this approach in the past. Also, will enamel paints bond well to krylon? Thanks. Quote Link to comment Share on other sites More sharing options...
big F Posted January 13, 2008 Share Posted January 13, 2008 I don't prime usually. It just makes it thicker and easier to rub off. I really should have said light mist more than coat/layer. only really a problem If you are using Auto paints or modeling stuff. Other than that as Skull says sand especially where parts will rub, unless your like me and it will just sit in a display case not being played with. Best of all if you can get the same paint as Skull or Krylon you A. O.K Quote Link to comment Share on other sites More sharing options...
rosedoggydog Posted January 17, 2008 Share Posted January 17, 2008 Why not RIT dye them instead? Probably about the easiest way of doing it. Get a junk cooking pot that you'll never eat out of again and give it a shot. If you don't like it you can still paint them. Quote Link to comment Share on other sites More sharing options...
Skull-1 Posted January 17, 2008 Share Posted January 17, 2008 (edited) THANKS Skull-1, I have actually considered just asking you if I can send all the parts to you to do a paint job for me. But I think I may try to learn myself and not burdon you with my issues of painting . I'm happy to help in any way I can. I *HAVE* used Krylon Fusion. Only because I couldn't get the color I wanted in any other brand. It works okay. No real problems with it that I have noted. Edited January 17, 2008 by Skull-1 Quote Link to comment Share on other sites More sharing options...
Skull-1 Posted January 17, 2008 Share Posted January 17, 2008 I really should have said light mist more than coat/layer. only really a problem If you are using Auto paints or modeling stuff. Other than that as Skull says sand especially where parts will rub, unless your like me and it will just sit in a display case not being played with. Best of all if you can get the same paint as Skull or Krylon you A. O.K Would that melt the plastic? Quote Link to comment Share on other sites More sharing options...
big F Posted January 18, 2008 Share Posted January 18, 2008 Would that melt the plastic? It was/is a technique I used for dyeing Parts when I used to Race RC cars We would dye gear sets in colours so that the pinions and gears for one set were all the same colour, you can't mix em up that way. it works on some plastics as well but IIRC it depends on how porous the plastic is and how much Nylon is in it. With Chunky's Im not sure on the contents of the plastic. Tamiya Used to do a kit with really loud colours but you can use fabric dyes and simmer for a few hours on the cooker plate. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.